Fabrication of 3D porous polyurethane-graphene oxide scaffolds by a sequential two-step processing for non-load bearing bone defects

Basit Öğe Kaydı
dc.contributor.authorBagheri, Fatemeh
dc.contributor.authorSaudi, Ahmad
dc.contributor.authorBidram, Elham
dc.contributor.authorAsefnejad, Azadeh
dc.contributor.authorSanati, Alireza
dc.contributor.authorZarrabi, Ali
dc.contributor.authorRafienia, Mohammad
dc.date.accessioned2024-05-19T14:46:15Z
dc.date.available2024-05-19T14:46:15Z
dc.date.issued2024
dc.departmentİstinye Üniversitesien_US
dc.description.abstractBone defects as a common orthopedic disease lead to severe pains over a long period. Scaffolds are novel approaches in tissue engineering to treat bone problems and deal with their challenges. Here, 3D porous polyurethane (PU) scaffolds containing graphene oxide (GO) with different percentages (0, 0.1, 0.3, and 0.5 wt%) were developed through a combination of freeze-drying and salt etching techniques for bone tissue engineering applications. The morphologies of scaffolds, physicochemical properties, the degree of crystallinity, and hydrophilicity were evaluated by SEM, FTIR, XRD, and water contact angle assay, respectively. The porosity, degradation behavior, compressive strength, and elastic modulus of 3D porous scaffolds were also determined. To assess the scaffold bioactivity, the morphology of the deposited calcium phosphate layer on the scaffold with macro-structure was evaluated by SEM images. The viability and adhesion of MG63 osteoblast-like cells cultured on the fabricated scaffolds were examined by MTT assay and SEM images, respectively. The results show that adding GO particles not only had no effect on the interconnectivity and porosity of 3D porous macroscopic structures of neat PU but also smaller and more uniformed microscopically pores were obtained. The crystallinity, water contact angle, and weight loss of scaffolds increased as the higher GO concentrations were employed. Followed by increasing GO contents from 0 to 0.5 wt%, the compressive strength and Young's modulus were increased by 232% and 245%, respectively. The bioactivity of scaffolds was fostered as GO concentration increased. Although, the MTT assay proved the biocompatibility of PU scaffolds containing 0.1 and 0.3 wt% GO, the samples loaded with 0.5 GO had a negative impact on the viability of MG63 cell lines. In conclusion, the present study demonstrates a high potential of PU scaffolds loaded with 0.1 and 0.3 wt% GO particles in bone tissue engineering applications.en_US
dc.identifier.doi10.1088/1402-4896/ad3289
dc.identifier.issn0031-8949
dc.identifier.issn1402-4896
dc.identifier.issue4en_US
dc.identifier.scopus2-s2.0-85188516862en_US
dc.identifier.scopusqualityQ2en_US
dc.identifier.urihttps://doi.org10.1088/1402-4896/ad3289
dc.identifier.urihttps://hdl.handle.net/20.500.12713/5481
dc.identifier.volume99en_US
dc.identifier.wosWOS:001188547500001en_US
dc.identifier.wosqualityN/Aen_US
dc.indekslendigikaynakWeb of Scienceen_US
dc.indekslendigikaynakScopusen_US
dc.language.isoenen_US
dc.publisherIop Publishing Ltden_US
dc.relation.ispartofPhysica Scriptaen_US
dc.relation.publicationcategoryMakale - Uluslararası Hakemli Dergi - Kurum Öğretim Elemanıen_US
dc.rightsinfo:eu-repo/semantics/closedAccessen_US
dc.snmz20240519_kaen_US
dc.subjectPolyurethaneen_US
dc.subjectGraphene Oxideen_US
dc.subjectFreeze-Dryingen_US
dc.subjectSalt Leachingen_US
dc.subjectBone Tissue Engineeringen_US
dc.titleFabrication of 3D porous polyurethane-graphene oxide scaffolds by a sequential two-step processing for non-load bearing bone defectsen_US
dc.typeArticleen_US

Dosyalar

Koleksiyon

WoS İndeksli Yayınlar Koleksiyonu
Scopus İndeksli Yayınlar Koleksiyonu